ZACHRY is currently seeking an experienced Industrial
Journeyman Pipe Fitter for new construction work.
An Industrial Pipe Fitter will assemble, layout, install
and maintain pipe systems on the new construction of a
Combined-Cycle Power Plant.
Must have 4+ years working as an Industrial Pipe Fitter
or Pipe Fitter Helper.
Must be able to read prints and illustrate thorough
knowledge of pipe fitting procedures and skills.
Must have good leadership and communication skills.
Must be have experience on an industrial construction
Read blueprints and specification to determine the scope
of work: locations, quantities, and sizes of materials
Identify all tools required for tasks.
Identify safety risks and the precautions required to
eliminate those risks.
Prepare, fabricate, install, and fit pipe to
Install valves, hangars, supports, flanges inside piping
system according to plans and applicable specifications.
Perform test to ensure the quality of the pipe and the
Hoist loads using slings, chains, shackles, hooks,
cables, and other rigging equipment.
Demonstrated industrial construction/maintenance history
Ability to read prints and construction drawings.
Ability to read and interpret technical manuals and
manufacturers manuals and instructions.
Demonstrate knowledge on the pipe fitting processes for
industrial piping and boiler components for a
combined-cycle power plant.
Must have 4+ years experience with the pipe fitting
Good problem-solving abilities.
Good aptitude and manual dexterity.
Good reading comprehension.
Ability to work with others – team player.
Ability to work independently – minimal supervision.
Good communication skills with co-workers and
Commitment to Zachry values and safety rules and
Zachry ROF’ed employee.
Former Zachry Employee.
NCCER Certification as an Industrial Pipe Fitter
Reports to Position
This position does not have any direct reports; however
the position will work closely with and oversee on
occasion of helper and labor positions. The position
will hold a positional and expertise authority of the
helper and laborer positions.
1 - Metal Tool Box with Lock
2 - Torpedo Magnetic Level
1 - 25' Tape Measure
1 - 5 Gallon Plastic Bucket
2 - 12" x 24" Framing Square
1 - String Level
1 - 8" Crescent Wrench
1 - 14" Pipe Wrench
1 - 24" Pipe Wrench
1 - Pipefitter's Blue Book
1 - 420 Channel Locks
1 - Torch Lighter (Striker)
1 - Chalk Line
1 - Set of Allen Wrenches
1 - Line Up Bar
2 - Combination Open/Box End Wrenches (7/8", 15/16", 1
1/16", 1 1/8", 1 1/4")
1 - Screwdriver (Flat)
1 - Set of Tip Cleaners
1 - Pair of Leather Gloves
1 - 24" Level
1 - 16' Tape Measure
1 - Pair of Cutting Goggles
1 - Center Finder
1 - 4" Wraparound
1 - 12" Crescent Wrench
1 - 18" Pipe Wrench
1 - Center Punch
1 - Wire Cutters
1 - Plumb Bob
1 - Set Blinding Wedges – Small
1 – Hacksaw
1 - 3lb to 4lb Ball Peen Hammer
1 - Phillips Screwdriver
1 - Combination Set -
, Protractor, and Center Finder
3/8 Ratchet Drive
with 3/8" to 1" set
1 - Construction Calculator
1 – Rain Suit
1 – Rubber boots
Employee will be required to adhere to large amounts of
standing, walking, bending, squatting and lifting.
Will talk and hear to communicate.
Must have good dexterity with hands and fingers to
perform the precision adjustments of machinery parts and
Will use arms and hands to signal, grab, hold, turn,
push, pull: objects, materials, controls and tools.
May be required to lift, carry and move up to 50lbs.
Will occasionally work at heights, climb ladders and
stairways and work off of platforms. Will work at
heights up to 300’ utilizing proper fall protection.
Will use vision abilities to focus, see short and long
distances, colors, depth perception and peripheral
Must be capable of working out side in the elements
including but not limited to the heat, cold, rain, snow
and wind; and must be able to work for long period of
times up to 12 hours a day.
Will be required to wear personal protective equipment
(PPE) including but not limited to: hard hat, safety
glasses/goggles, ear plugs/muffs, masks/respirators,
safety vests, gloves and steel-toe boots.